Plumbing for Beginners: The Essentials for Bathtub Installation
Plumbing for Beginners: The Essentials for Bathtub Installation
Blog Article
Do you find yourself hunting for critical information around How to Install a Bathtub Yourself?
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a moderately challenging job. If the old tub is easily easily accessible, the task can relocate easily; if you have to open a wall to remove the old bathtub as well as place the new tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly need a helper to leave the old tub and embeded in the new one. Make sure you have actually qualified on your own for the job and also are comfortable trying it. Rather than working with a specialist to take over a halfway-completed job, it is far better to think about using one before you begin. Possibilities are you might need an expert plumber to make tube links.
This write-up will help you set up a brand-new bath tub in your bathroom if you have already gotten a brand-new bathtub and also do not require to transform the setup of your previous supply of water pipelines.
Your tools as well as material list should make up the following:
Preparing for the Installation
To start with, the supporting frame provided with the bath should be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets device to prevent stress on the tub.
Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must now prepare to be fitted in its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be fairly problematic due to the restricted access that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a cloth all set for the continuing to be water that will originate from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from transforming during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Bath tub
Making use of the two wood boards under its feet, put the bathtub in the called for position. The wood boards are valuable in evenly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four tiny factors.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by inspecting the level and changing the feet on the bath tub until the spirit level checks out degree.
To mount faucets, fit all-time low of the outermost flexible tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water and also examine all joints and also brand-new pipework for leaks and tighten them if necessary. Load the bath tub as well as likewise check the overflow electrical outlet and the regular outlet for leakages.
Lastly, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the tub should wait till the tub has actually been used at least when as this will settle it right into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic port to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the placing hole in the bath/basin guaranteeing that the washers are in area in between the tap and also the sink. Secure the tap in place with the maker supplied backnut. Once the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The previous kind ought to be attached to the tap finishes initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bathroom fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to fracture a rigid seal, causing the water to pass through the wall surface in between the bathroom and also the tiling, leading to complications with moisture as well as feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components and also installations. They are sold in tubes and cartridges, and also can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the bath tub with water before securing, to enable the movement experienced when the tub is in use. The sealer can crack fairly very early if you do not take into account this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the market. It is recommended to fit the floor tiles utilizing waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that article on A Step-by-Step Guide to Installing a Bathtub when browsing the search engines. Be sure to take a moment to share this blog posting if you liked it. Thanks a lot for your time. Don't hesitate to check our site back soon.
Customer Reviews Report this page